How do I know this chain fits my saw?

Match three numbers: pitch, gauge, and drive-link count. All three must match the stamp on your current bar. If even one is off, the chain won't fit safely.

How do I measure pitch and gauge?

Pitch is the distance between any three consecutive rivets, divided by two. Gauge is the thickness of the drive links — measure with a caliper or check the bar stamp. Our guide covers both in detail.

How long does a replacement chain last?

With proper tension and occasional sharpening, an aftermarket chain lasts 3–5 cords of firewood or about 5 hours of active cutting — roughly the same as OEM.

Can I sharpen this chain or is it single-use?

Absolutely sharpen it. A quality replacement chain can be sharpened 3–5 times before the cutters are too short. Keep a round file matched to the cutter diameter.

2PC 16 Inch Chainsaw Chain

Name: 2PC 16 Inch Chainsaw Chain
Brand: OPULADUO
SKU: B0DBLPG78L
Price: 21.98 USD
Availability: InStock
Rating: 4.7 (1 reviews)

Overview

This chain is manufactured to OEM specs for Husqvarna 120 (MII) /130/135 (MII) / 240 saws, providing dependable cutting performance as an aftermarket alternative. Comes in a convenient 2-pack, giving you a ready spare. Replacing a stretched or damaged chain restores both cutting speed and operator safety.

Key specifications

Bar length: 16”
Quantity: 2 chains per pack

Compatibility

Fits Husqvarna 120 (MII) /130/135 (MII) / 240 as a direct replacement for the factory chain. Always confirm your saw’s model number and bar length before ordering to ensure proper fit.

Installation notes

Disconnect the spark plug wire or remove the battery before changing a chainsaw chain. Remove the bar cover, release bar tension, and take off the old chain. Place the new chain into the bar groove with the cutting teeth facing forward on top. Reinstall the cover, adjust chain tension until snug, and test by pulling the chain around the bar by hand. Re-check tension after a few minutes of use.

Common questions

Q: Will this 2-pack 16 inch chain fit my Husqvarna 135 Mark II with the stock 16” bar?

Yes, this chain is made for Husqvarna 135 (MII) models using a 16 inch bar, and it also fits the Husqvarna 120 (MII), 130, and 240 listed in the compatibility info. To be safe, confirm your saw is running the original 16” setup and match the chain specs from your current bar or owner’s manual before installing.

Q: I have a Husqvarna 240 with a 16” bar — do both chains come ready to install, and do I need to adjust tension right away?

Yes, both chains are replacement loops for a 16 inch setup, so they install the same way as your original chain on a Husqvarna 240. After fitting the chain, set the tension so the drive links stay engaged in the bar groove but the chain still pulls around by hand, then recheck it after the first few minutes of cutting since a new chain will usually stretch slightly.

Q: How should I maintain these 16 inch chains on my Husqvarna 120 Mark II so they last longer?

Keep the chain properly tensioned, make sure bar oil is flowing well, and touch up the cutters with the correct file size as soon as cutting performance drops. It also helps to clean the bar groove and check the drive sprocket for wear each time you swap chains, especially since this is a 2-pack and rotating chains can extend bar and sprocket life.

Before you buy — how to verify fitment

Find the bar stamp. Look on the side of your current guide bar for the pitch, gauge, and drive-link count.
Match all three numbers. Pitch (3/8 LP), gauge (.050"), and drive links (56DL) must all match.
Check bar length. Measure cutting length from the tip to where the bar enters the saw body — this should match 16".
Confirm your saw model against the compatibility list above. If your model isn't listed, the chain may still fit if pitch/gauge/DL match.