2PC 16 Inch Chainsaw Chain

§ Saw Chains · SKU B0D9VC8QNK

2PC 16 Inch Chainsaw Chain

$22 ★ 4.3

2PC 16 Inch Chainsaw Chain for Makita XCU04 / XCU04Z / XCU04CM Chainsaw, 16" Replacement Chain for Makita XCU04PT / XCU04PT1 Chain Saw

Bar length16"
Pitch3/8 LP"
Gauge.043""
Drive links56DL
CategorySaw Chains
Part numberB0D9VC8QNK
ConditionNew — aftermarket replacement

Fitment last verified:

Compare similar parts Check price & availability


Overview

Built for Makita XCU04 / XCU04Z / XCU04CM Chainsaw chainsaws, this replacement chain delivers consistent cuts and reliable durability at a fraction of OEM cost. Ships as a 2-piece set, giving you a ready spare. Replacing a stretched or damaged chain restores both cutting speed and operator safety.

Key specifications

  • Bar length: 16”
  • Quantity: 2 chains per pack

Compatibility

Manufactured to fit Makita XCU04 / XCU04Z / XCU04CM Chainsaw without modification. Check your owner’s manual or the existing chain’s markings to verify pitch, gauge, and drive link count before ordering.

Installation notes

Begin by shutting off the saw and disconnecting the power source. Loosen the bar-mounting fasteners and remove the side cover to access the chain. Slide the worn chain off, seat the replacement around the sprocket and into the bar groove with cutters pointing in the direction of rotation. Tighten the tensioning screw until there is slight play but no droop, then secure the cover.

Common questions

Q: Will this 2-pack 16 inch chain fit my Makita XCU04Z, or does it only work with the XCU04 and XCU04CM?

Yes, these 16 inch saw chains are made to fit the Makita XCU04, XCU04Z, and XCU04CM. If your saw is one of those 16-inch XCU04-series models and you are using the matching 16-inch bar, this replacement chain is the correct fit.

Q: Do I need to do anything special when installing this chain on my Makita XCU04CM?

Make sure the chain is installed with the cutting edges facing forward on the top side of the bar, then set the tension so the chain snaps back lightly but still pulls around by hand. After the first few cuts, recheck tension because a new chain can stretch slightly as it seats in.

Q: How often should I sharpen or replace these 16 inch chains on an XCU04?

Sharpen the chain whenever you notice slower cutting, fine sawdust instead of chips, or if the saw starts pulling to one side. Keep the bar groove clean and maintain proper chain oil flow, since good lubrication and regular touch-ups will help both chains in the 2-pack last much longer.

Compatibility

This part is verified to fit the following equipment. Always confirm the model number stamped on your machine before ordering.

Makita XCU04
XCU04Z
XCU04CM Chainsaw

Not sure which chain you need? See our guide: How to count drive links or Chain pitch, gauge & drive links explained.

Before you buy — how to verify fitment

  1. Find the bar stamp. Look on the side of your current guide bar for the pitch, gauge, and drive-link count.
  2. Match all three numbers. Pitch (3/8 LP), gauge (.043"), and drive links (56DL) must all match.
  3. Check bar length. Measure cutting length from the tip to where the bar enters the saw body — this should match 16".
  4. Confirm your saw model against the compatibility list above. If your model isn't listed, the chain may still fit if pitch/gauge/DL match.

Frequently asked questions

How do I know this chain fits my saw?

Match three numbers: pitch, gauge, and drive-link count. All three must match the stamp on your current bar. If even one is off, the chain won't fit safely.

How do I measure pitch and gauge?

Pitch is the distance between any three consecutive rivets, divided by two. Gauge is the thickness of the drive links — measure with a caliper or check the bar stamp. Our guide covers both in detail.

How long does a replacement chain last?

With proper tension and occasional sharpening, an aftermarket chain lasts 3–5 cords of firewood or about 5 hours of active cutting — roughly the same as OEM.

Can I sharpen this chain or is it single-use?

Absolutely sharpen it. A quality replacement chain can be sharpened 3–5 times before the cutters are too short. Keep a round file matched to the cutter diameter.

Where to buy

This part is available through Amazon with free returns on most orders. We've verified the fitment listed above — check the live listing for current price, stock, and delivery options.

Check current price on Amazon

Affiliate disclosure: we may earn a commission when you purchase through this link, at no extra cost to you.

§ Compare

Similar Saw Chains

§ Guides

Related how-to guides