2PC 12 Inch Chainsaw Chain

§ Saw Chains · SKU B0FRDNJG6X

2PC 12 Inch Chainsaw Chain

$19 ★ 5.0

2PC 12 Inch Chainsaw Chain for HART HGCS02 / HGCS021 / HGCS021VNM, 12" Replacement Chain for HART HGCS02BT Chainsaw

Bar length12"
Pitch3/8 LP"
Gauge.043""
Drive links45DL
CategorySaw Chains
Part numberB0FRDNJG6X
ConditionNew — aftermarket replacement

Fitment last verified:

Compare similar parts Check price & availability


Overview

Built for HART HGCS02 / HGCS021 / HGCS021VNM chainsaws, this replacement chain delivers consistent cuts and reliable durability at a fraction of OEM cost. Sold as a 2-pack, giving you a ready spare. Chains wear down over time from regular use, and a fresh chain cuts faster and safer than a dull one.

Key specifications

  • Bar length: 12”
  • Quantity: 2 chains per pack

Compatibility

This chain is designed to fit HART HGCS02 / HGCS021 / HGCS021VNM. Verify your specific model number and existing chain dimensions before purchasing.

Installation notes

Disconnect the spark plug wire or remove the battery before changing a chainsaw chain. Remove the bar cover, release bar tension, and take off the old chain. Place the new chain into the bar groove with the cutting teeth facing forward on top. Reinstall the cover, adjust chain tension until snug, and test by pulling the chain around the bar by hand. Re-check tension after a few minutes of use.

Common questions

Q: Will this 2-pack 12 inch chainsaw chain fit my HART HGCS021VNM, or is it only for the HGCS02?

Yes, this chain is made to fit the HART HGCS02, HGCS021, and HGCS021VNM with a 12-inch bar. If your saw is one of those exact models and still uses the original 12-inch setup, these chains should install correctly.

Q: Do I need to replace both chains at once, and how should I maintain them on my 12-inch HART saw?

You do not need to install both at the same time; the second chain is typically kept as a spare so you can swap it in when the first gets dull. For best performance, keep the chain properly tensioned, make sure the bar oil reservoir stays full, and touch up the cutters regularly so the saw cuts smoothly without forcing it.

Q: Is this replacement chain difficult to install on the HART HGCS021, and how do I know if the tension is right afterward?

Installation is usually straightforward: loosen the side cover, place the chain around the sprocket and 12-inch bar, then adjust the tension before tightening everything back down. The chain should sit snugly on the bar but still pull around by hand with a gloved hand, without hanging loose underneath.

Compatibility

This part is verified to fit the following equipment. Always confirm the model number stamped on your machine before ordering.

HART HGCS02
HGCS021
HGCS021VNM

Not sure which chain you need? See our guide: How to count drive links or Chain pitch, gauge & drive links explained.

Before you buy — how to verify fitment

  1. Find the bar stamp. Look on the side of your current guide bar for the pitch, gauge, and drive-link count.
  2. Match all three numbers. Pitch (3/8 LP), gauge (.043"), and drive links (45DL) must all match.
  3. Check bar length. Measure cutting length from the tip to where the bar enters the saw body — this should match 12".
  4. Confirm your saw model against the compatibility list above. If your model isn't listed, the chain may still fit if pitch/gauge/DL match.

Frequently asked questions

How do I know this chain fits my saw?

Match three numbers: pitch, gauge, and drive-link count. All three must match the stamp on your current bar. If even one is off, the chain won't fit safely.

How do I measure pitch and gauge?

Pitch is the distance between any three consecutive rivets, divided by two. Gauge is the thickness of the drive links — measure with a caliper or check the bar stamp. Our guide covers both in detail.

How long does a replacement chain last?

With proper tension and occasional sharpening, an aftermarket chain lasts 3–5 cords of firewood or about 5 hours of active cutting — roughly the same as OEM.

Can I sharpen this chain or is it single-use?

Absolutely sharpen it. A quality replacement chain can be sharpened 3–5 times before the cutters are too short. Keep a round file matched to the cutter diameter.

Where to buy

This part is available through Amazon with free returns on most orders. We've verified the fitment listed above — check the live listing for current price, stock, and delivery options.

Check current price on Amazon

Affiliate disclosure: we may earn a commission when you purchase through this link, at no extra cost to you.

§ Compare

Similar Saw Chains

§ Guides

Related how-to guides