2PC 8 Inch Polesaw Chain

§ Saw Chains · SKU B0BMFWQ5P4

2PC 8 Inch Polesaw Chain

$17 ★ 4.6

2PC 8 Inch Polesaw Chain for Sun Joe SWJ800E SWJ806E SWJ802E, 8" Replacement Chain for WEN 4019-3/8" - .050" - 33 DL

Bar length8"
Pitch3/8"
Gauge.050""
Drive links33DL
CategorySaw Chains
Part numberB0BMFWQ5P4
ConditionNew — aftermarket replacement

Fitment last verified:

Compare similar parts Check price & availability


Overview

Comes in a convenient 2-pack, this chain is a direct replacement for Sun Joe SWJ800E SWJ806E SWJ802E models. A sharp chain means less effort, cleaner cuts, and safer operation compared to pushing through wood with worn teeth.

Key specifications

  • Bar length: 8”
  • Pitch: 3/8”
  • Gauge: .050”
  • Drive links: 33 drive links
  • Quantity: 2 chains per pack

Compatibility

Engineered for direct compatibility with Sun Joe SWJ800E SWJ806E SWJ802E. Verify your specific model number and existing chain dimensions before purchasing.

Installation notes

Disconnect the battery or unplug the pole saw before beginning any chain work. Remove the bar cover, take off the spent chain, and lay the new one into the bar groove with teeth oriented in the correct cutting direction. After reattaching the cover, set the chain tension so there is slight play but no sag under the bar. Run the saw briefly and recheck tension after the chain seats itself.

Common questions

Q: Will this 2-pack 8 inch polesaw chain fit my Sun Joe SWJ806E, and does it also work on the SWJ800E and SWJ802E?

Yes, this chain is made to fit Sun Joe SWJ800E, SWJ806E, and SWJ802E pole saws that use an 8-inch bar. It uses a 3/8 pitch, so it matches the drive setup those compatible models are designed for.

Q: Do I need any special tools to install this 8 inch chain on my Sun Joe SWJ802E?

You typically only need the basic bar/side cover adjustment hardware already on the saw, plus a screwdriver or wrench depending on your model. Make sure the chain is installed in the correct cutting direction, then adjust the tension so it sits snug on the 8-inch bar but still pulls around by hand.

Q: How often should I sharpen or replace this 3/8 pitch polesaw chain if I use my SWJ800E for trimming small branches?

If the chain starts producing fine sawdust instead of wood chips, pulls to one side, or requires extra pressure to cut, it likely needs sharpening. Keep the chain properly oiled and tensioned, and replace it when the cutters are too worn or the chain no longer holds an edge well.

Compatibility

This part is verified to fit the following equipment. Always confirm the model number stamped on your machine before ordering.

Sun Joe SWJ800E SWJ806E SWJ802E

Not sure which chain you need? See our guide: How to count drive links or Chain pitch, gauge & drive links explained.

Before you buy — how to verify fitment

  1. Find the bar stamp. Look on the side of your current guide bar for the pitch, gauge, and drive-link count.
  2. Match all three numbers. Pitch (3/8), gauge (.050"), and drive links (33DL) must all match.
  3. Check bar length. Measure cutting length from the tip to where the bar enters the saw body — this should match 8".
  4. Confirm your saw model against the compatibility list above. If your model isn't listed, the chain may still fit if pitch/gauge/DL match.

Frequently asked questions

How do I know this chain fits my saw?

Match three numbers: pitch, gauge, and drive-link count. All three must match the stamp on your current bar. If even one is off, the chain won't fit safely.

How do I measure pitch and gauge?

Pitch is the distance between any three consecutive rivets, divided by two. Gauge is the thickness of the drive links — measure with a caliper or check the bar stamp. Our guide covers both in detail.

How long does a replacement chain last?

With proper tension and occasional sharpening, an aftermarket chain lasts 3–5 cords of firewood or about 5 hours of active cutting — roughly the same as OEM.

Can I sharpen this chain or is it single-use?

Absolutely sharpen it. A quality replacement chain can be sharpened 3–5 times before the cutters are too short. Keep a round file matched to the cutter diameter.

Where to buy

This part is available through Amazon with free returns on most orders. We've verified the fitment listed above — check the live listing for current price, stock, and delivery options.

Check current price on Amazon

Affiliate disclosure: we may earn a commission when you purchase through this link, at no extra cost to you.

§ Compare

Similar Saw Chains

§ Guides

Related how-to guides