Opuladuo RYOBI PCLCW01 / PCLCW01B / PCLCW01K 6 Pruning Chain

This Opuladuo 6-inch pruning chain is intended for specific RYOBI pruning saws: PCLCW01, PCLCW01B, and PCLCW01K. If you need a 6 in. replacement chain for a RYOBI PCLCW01-series pruning saw, this listing is designed around those exact models.

Will this chain fit your saw?

This chain is for the following models listed by the manufacturer:

• RYOBI PCLCW01
• RYOBI PCLCW01B
• RYOBI PCLCW01K

The original listing is very specific: this 6 inch chainsaw chain is only for RYOBI PCLCW01 chainsaws, and other 6-inch chainsaws are not compatible. That matters because chains that look similar can still differ in pitch, gauge, or drive-link count, and even a small mismatch can cause poor cutting, chain derailment, or bar/drive damage.

Before ordering, confirm these points on your current saw or chain:

• Model number on the tool matches PCLCW01, PCLCW01B, or PCLCW01K
• Bar length is 6 inches
• Chain pitch matches your original chain
• Chain gauge matches your bar groove
• Drive-link count matches the chain that came off your saw

If your old chain is still available, the safest check is to compare it directly to the replacement you need. The saw model is the first filter, but chain size details still matter when replacing any chainsaw chain. If your bar or chain markings show pitch, gauge, and drive-link count, make sure those match your original setup.

What’s included here:

• 2 pcs 6-inch chain

That gives you one chain to install now and one to keep sharpened and ready as a spare.

Replacing the chain

Always remove the battery from your pruning saw before handling the chain or bar.

1. Remove the battery and let the saw fully stop.
2. Loosen the side cover or chain-retention hardware according to your saw’s manual, then remove the old chain carefully while wearing gloves.
3. Clean debris from the bar groove, sprocket area, and side cover before installing the new chain.
4. Fit the new 6-inch chain onto the bar and drive sprocket, making sure the cutter direction matches the saw’s normal cutting rotation.
5. Reinstall the cover and adjust chain tension so the chain sits in the bar groove properly and can still be pulled around by hand with a gloved hand.
6. Recheck tension after a few test cuts, since a new chain can settle in quickly.

If you are unsure about cutter direction, compare the new chain to the one you removed before installation. Installing a chain backward is a common mistake and will prevent proper cutting.

Keeping it sharp

A small pruning chain cuts best when it stays clean and properly tensioned.

• Avoid cutting dirty wood or letting the chain contact soil. Grit dulls cutters very quickly.
• Check chain tension often, especially during the first few uses after installation.
• Touch up or replace the chain when it starts producing fine dust instead of chips, pulls to one side, or requires extra pressure to cut.

Because this package includes 2 chains, many users keep one installed and one sharpened spare on hand. That makes it easier to swap chains and get back to work without downtime.

FAQ

Will this fit any 6-inch mini chainsaw?

No. The listing states this chain is only for RYOBI PCLCW01 chainsaws. Other 6-inch chainsaws are not considered compatible just because they use a 6-inch bar.

What RYOBI versions does this fit?

It is listed for PCLCW01, PCLCW01B, and PCLCW01K. If your saw shows one of those exact model numbers, this is the intended fitment.

Does the package include one chain or more?

The package includes 2 pcs 6-inch chain.

Do I need to verify anything besides the model number?

Yes. It is smart to also confirm your original chain’s bar length, pitch, gauge, and drive-link count before replacing it, especially if your saw has had parts changed previously.