EGO CS1613 Chain — Best Aftermarket 16-Inch for the Top-Selling Battery Saw

If you own an EGO 16-inch battery chainsaw, you’ve probably seen the same complaint come up again and again in owner forums and community discussions: the saw itself is excellent, but replacement chains can feel overpriced, hard to find locally, or a little confusing to match correctly across similar EGO model numbers. That’s especially relevant for the EGO CS1613, which has become one of the most highly rated battery chainsaws in its class. When a saw gets that popular, owners inevitably start looking for better-value consumables.

A chain is a wear item. If you cut regularly, hit dirty wood, catch a rock, or accidentally touch the ground even once, performance can drop fast. Having a spare chain on hand is less of a luxury and more of a necessity. That’s why this 2-pack aftermarket replacement set has gotten so much attention: it offers an Oregon-spec 16-inch replacement chain for multiple EGO saws at a price that undercuts OEM by a wide margin.

The Problem

For most EGO chainsaw owners, the issue isn’t the saw motor or battery platform—it’s chain wear and replacement cost.

The common failure modes are pretty predictable:

• Dulling from dirty wood or ground contact: Even a brief touch into soil can take the edge off cutters immediately.
• Stretch over time: New chains often need repeated tension adjustments during early use, and older chains can eventually become difficult to tension properly.
• Uneven cutting or curved cuts: If one side of the chain dulls more than the other, the saw may start pulling to one side.
• Burning, smoke, or slow cutting: A dull or damaged chain creates more friction, makes the saw work harder, and reduces runtime.
• Chipped or damaged cutters: Hidden nails, fencing, or embedded debris in storm-fallen wood can ruin a chain quickly.

Owners of the EGO CS1613, CS1604, and CS1600 often mention a practical annoyance: OEM replacement chains are good, but paying $30 or more for a single chain adds up quickly if you use the saw regularly. For homeowners who cut firewood, clean up storm debris, or maintain acreage, it makes sense to stock replacements. That’s where a quality aftermarket option becomes attractive—if the fit and cutting performance are right.

Our Pick

The standout value option here is:

2PC 16 Inch Chainsaw Chain Replacement for EGO Power+ CS1613 / CS1604 / CS1600 / CS1610 / CS1611 16-Inch 56V Chainsaw
ASIN: B0BTBW64DQ
Price: $21.99
Rating: 4.5/5

This listing gives you two 16-inch replacement chains for less than the cost of many single OEM chains. That alone makes it worth a close look, but the bigger reason it stands out is that it’s marketed as an Oregon-spec aftermarket chain, which is exactly the kind of language EGO owners tend to look for. Oregon is a trusted benchmark in chainsaw chain geometry and fitment, and owners generally want something that matches OEM performance as closely as possible without OEM pricing.

Why this is a strong buy:

• Excellent value: At $21.99 for 2, you’re paying about $11 per chain
• Fits multiple EGO 16-inch models: Helpful if you own more than one saw or are buying for family
• Good owner feedback: A 4.5-star rating suggests real-world satisfaction, especially important for aftermarket wear parts
• Makes sense as a backup set: Even if you prefer OEM for primary use, these are affordable enough to keep as ready-to-install spares

For a chainsaw chain, “value” doesn’t just mean low cost. It means the chain installs correctly, tensions normally, tracks well on the bar, cuts cleanly, and doesn’t create odd oiling or fitment problems. Based on the strong reception this model has received in owner discussions, this one appears to hit that sweet spot.

Compatibility

This replacement chain is listed for the following EGO Power+ 16-inch 56V chainsaw models:

• EGO CS1613
• EGO CS1604
• EGO CS1600
• EGO CS1610
• EGO CS1611

That model coverage matters because EGO’s naming can be confusing, and not every 16-inch bar setup across power tool brands uses the same chain specs. If you’re shopping quickly, always match the exact saw model number from the label on the tool rather than assuming all 16-inch chains are interchangeable.

The CS1613 is the key model for many buyers here. Since it’s one of the top-rated battery chainsaws on the market, replacement parts for it are in high demand. If you bought the CS1613 as a bare tool or in a kit and want a more affordable ongoing maintenance option, this 2-pack is specifically aimed at that use case.

Before ordering, it’s still smart to verify:

• The exact model number on your saw
• The chain specs printed on your current bar or original chain
• Whether your saw is using the factory 16-inch bar setup

If your saw has been modified with a non-original bar, double-check dimensions before purchase.

Installation Tips

Swapping a chain on an EGO battery chainsaw is straightforward, but there are a few gotchas worth mentioning.

1. Remove the battery first
   Always take out the 56V battery before touching the chain or bar.

2. Open the side cover and remove the old chain
   Loosen the cover, back off chain tension, and slide the bar and chain free.

3. Clean the bar groove and sprocket area
   This is a good time to remove packed sawdust, check the bar oil hole, and inspect the drive sprocket.

4. Install the new chain in the correct direction
   This is the most common mistake. On the top edge of the bar, the cutter teeth should face forward.

5. Set tension carefully
   Don’t overtighten. The chain should lift slightly from the bar but still snap back into place and move freely by hand with gloves on.

6. Recheck after a short cut session
   New chains often stretch a bit at first. After a few minutes of use, check tension again.

A couple of practical notes:

• If the saw cuts crooked after installation, it may not be the new chain alone—inspect bar wear too.
• Keep chain oil topped off. A dry chain will wear out quickly, no matter what brand you buy.
• If you sharpen your own chains, mark rotation order so you can keep one ready while the other is being serviced.

Watch: Video Guide

If you want a visual walkthrough for chain replacement and general setup, here’s the video guide:

Why This Over OEM?

The biggest reason is simple: price.

If the OEM EGO replacement chain is $30+ for one chain, and this aftermarket set is $21.99 for two chains, the math is hard to ignore.

Approximate comparison:

• OEM: $30+ each
• Aftermarket 2-pack: $21.99 total
• Effective cost per chain: about $11

That means you could buy two aftermarket chains for less than one OEM chain, and still have money left over.

Beyond cost, there are two more advantages:

1. Better backup readiness

Chains are consumables. When a chain gets damaged during cleanup or weekend cutting, it’s much more convenient to swap in a spare immediately than to stop and sharpen. A 2-pack supports that.

2. Availability

OEM parts can be inconsistent depending on the season, local inventory, or whether your dealer stocks EGO consumables. Aftermarket chains that are clearly labeled for the CS1613/CS1604 family can be easier to order quickly.

As for quality, it’s important to be honest: OEM is still the safest default if you want guaranteed factory match and don’t mind paying for it. But for many homeowners, this isn’t a high-risk experiment. The product is well reviewed, uses Oregon-spec fitment as a selling point, and is widely praised in owner forums for delivering solid everyday performance at a much lower price.

In other words, this is not just “cheap.” It appears to be one of the better-value aftermarket choices specifically because it aligns with what EGO owners actually want: acceptable cut quality, proper fit, and a meaningful price advantage.

FAQ

1. Will this definitely fit my EGO CS1613?

It’s listed specifically for the EGO CS1613, along with CS1604, CS1600, CS1610, and CS1611. Still, you should confirm the exact model number on your saw and compare against your current bar/chain specs before ordering.

2. Is this as good as the OEM EGO chain?

For many homeowners, it’s likely close enough to make the savings worthwhile. OEM still has the edge for guaranteed factory-spec confidence, but this aftermarket option is well rated and widely praised for value and fitment. If you cut casually or want affordable spares, it makes a lot of sense.

3. Should I buy this even if my current chain can still be sharpened?

Yes, if you use your saw regularly. A spare chain is one of the most useful things to keep on hand. You can continue sharpening your original chain while keeping one of these installed or ready as a backup.

If you own an EGO CS1613 or another compatible 16-inch model and want to cut your replacement-chain cost dramatically without stepping into no-name junk territory, this 2-pack replacement chain set (ASIN B0BTBW64DQ) is a very sensible buy. At $21.99 for two chains, it solves a common owner complaint with a straightforward, practical value proposition.