2PC 16 Inch Chainsaw Chain for Craftsman CMECS600 / S165 / S160 Chainsaw

This 2-piece 16-inch replacement chainsaw chain set is made for select Craftsman saws, including the Craftsman CMECS600, S165, and S160. It is also listed for Craftsman CMXGSAMN4216, making it a practical match when you need a fresh chain for routine cutting, storm cleanup, or general property maintenance.

Because chains must match both the saw and the guide bar, it is important to confirm fitment before ordering or installing. A chain that is the right length but the wrong pitch, gauge, or drive-link count will not run correctly.

Will this chain fit your saw?

This product is listed as a:

• 16 Inch Chainsaw Chain Replacement for Craftsman CMECS600 Chainsaw
• 16 Inch Chainsaw Chain Replacement for Craftsman S165 / S160 Chain Saw
• 16 Inch Chainsaw Chain Replacement for Craftsman CMECS600 / S165 / S160 / CMXGSAMN4216 Chainsaw

If you own one of those models, this chain is intended for your saw. The package includes:

• 2Pcs 16-Inch Chain

To confirm fitment, check these four details on your current chain or guide bar:

• Bar length: This replacement is for a 16-inch bar.
• Pitch: The spacing between chain links must match the drive sprocket and bar tip.
• Gauge: The thickness of the drive links must match the bar groove.
• Drive-link count: The total number of drive links must match the bar and saw setup.

The easiest way to verify is to look at the markings stamped on the guide bar. Many bars list the required pitch, gauge, and drive-link count. You can also compare against the specifications printed in your saw’s owner’s manual. If your Craftsman saw is a CMECS600, S165, S160, or CMXGSAMN4216 with a 16-inch bar, that is the first and most important fitment checkpoint.

If your saw has had the bar replaced at some point, do not rely on model number alone. A replacement bar may use a different chain specification than the original setup, so always match the new chain to the bar currently installed on the saw.

Replacing the chain

Before starting, unplug the saw or otherwise make sure it cannot power on accidentally. Wear gloves when handling the chain.

1. Remove power and let the saw cool completely.
2. Loosen the side cover and back off the chain tension so the old chain can be removed from the bar and drive sprocket.
3. Clean debris from the bar groove, sprocket area, and oil outlet before installing the new chain.
4. Fit the new chain around the drive sprocket and along the guide bar, making sure the cutting edges face the correct direction on the top of the bar.
5. Reinstall the side cover, then adjust chain tension until the chain sits snugly in the bar groove but can still be pulled by hand with a gloved hand.
6. Recheck tension after a short test run, since a new chain can seat in and loosen slightly.

If the chain seems too loose or too tight even after adjustment, stop and recheck that the bar length and chain specifications match your saw.

Keeping it sharp

A sharp chain cuts faster, puts less strain on the motor, and is safer to use than a dull one.

• Keep the chain properly tensioned. A loose chain can derail, while an overly tight chain can wear the bar and drive components faster.
• Avoid cutting into dirt, rocks, or fencing. Even brief contact can dull the cutters quickly.
• Maintain chain lubrication. Proper bar-and-chain oil flow reduces heat and helps both the chain and guide bar last longer.

If you notice fine sawdust instead of chips, wandering cuts, or the need to force the saw through wood, it is usually time to sharpen the chain or replace it.

FAQ

Does this include one chain or two?

This package includes 2Pcs 16-Inch Chain.

Will this fit any 16-inch Craftsman chainsaw?

Not automatically. A 16-inch bar is only one part of fitment. You also need the correct pitch, gauge, and drive-link count, and this chain is specifically listed for Craftsman CMECS600, S165, S160, and CMXGSAMN4216.